PRODUCTS

Intelligent Tumbler Dryer

Structure and Function of Intelligent Tumbler Dryer

 

1.    The machine set soft capsules dry, wash pills and polished in one of the intelligent equipment.

 

A drying line consists of one or more units, each containing 75 kg of capsules. A unit for the 2-cage, the frame using aluminum alloy. The shell is enclosed by a 304 plate and an acrylic plate, in front of four acrylic panels. The upper part is loaded capsule two sections, the lower part is the rotor dehumidifier unit. The middle is the oil tray, sealed with the shell to prevent oil into the lower part of the oil.

 

Dehumidifier dry wind by the dehumidifier fan sent to the upper part of the internal circulation of the air box, the treatment of wind from the top through the pipeline back to the lower dehumidifier, and electrostatic filter into the dehumidifier unit. Two sections of the cage separated by the acrylic plate, the upper part of the circulation fan compartment separated, each section installed two 1500 air flow fan, air shower dry soft capsule, each section cage has 1500 * 2 = 3000 air circulation, The upper volume of 1.2 cubic meters, 2500 times per hour cycle. Each section of the cage has a gear motor drive, cage speed by the inverter speed, the fastest 18 rev / min. Reducer installed in the upper right corner of the machine, with stainless steel plate and rotor isolation oil will not enter the slowdown chassis. Each cage has a bracket with a roller, and the cage is mounted on the bracket, and after opening the front plexiglass door, the carriage and cage can be pulled together to the van.

 

The use of units can buy an automatic cage cleaning machine, transfer truck cage to the automatic cleaning machine next to the bracket and cage into the washing machine for automatic cleaning. The middle of the oil tray has a pipe connection below the storage tank, and then on a regular basis. The top button box has a number of temperature and humidity sensors, stop the reverse button and status indicator, running the normal indicator and fault lights. Inside the top with LED lights.

 

tumblerdryerp24智能转笼

 

Welcome to contact our professional sales engineer for further support at sec@secsoftgel.com


2.    Each unit has an independent PLC control, control dehumidifier regenerative heating temperature controller, cold water switch, cage speed, rotation direction and so on. Can detect each section cage temperature, humidity, cage drive inverter working conditions, cold water pressure, acrylic door is closed, whether the exhaust fan work, electrical power is normal and whether the temperature limit beyond the protection.
 

3.    There are a number of units connected into a smart drying line, PLC is divided into the host and slave, the master station control the slave, coordinate the coordination and coherence between the units, according to each section humidity control dehumidification unit working temperature and energy optimization management. The touch screen man-machine interface communicates with the device through the network router, can read the parameters of the equipment, and communicate the instructions of the operator to the PLC. The Internet can also connect the device and the person to the Internet (user option), that is, the operator and Managers can monitor the status and failure status of each unit over the network.

 

  • Power of in-cage air shower fan:  0.4KW*4=1.6Kw
  • Regenerative wind electricity heating:  9*0.8Kw=7.2Kw  Solid-state relay control
  • Transmission power: 0.4KW*2=0.8KW
  • Power of main fan: 0.75KW*2=1.5KW
  • Designed wind flux of dehumidifying dish: 1,600m3/h Volume air exchanger 900 times/h
  • Water removal 3kg/H Drain from workshop through upper discharge fan
  • Power supply AC380V 3P 5L / 220V
  • Compressed air supply 4kp
  • Water chilling unit Concentrated supply 2.5P multiply by number of units 
  • Basket Size Diameter 1000mm Length 1000mm
  • Maximum loading quantity of basket 120kg
  • Work loading quantity of basket 80~120kg
  • Regenerative heat and humidity air quantity 200m3/h Discharge out of workshop
  • Dimension Length 2400* Width 1380* Height 1915
  • Workshop environment Normal/25°C RH55%

 

CONTACT US

Name *

Email *

Mobile Phone *

Company Name *

Your Questions *

PRODUCTS

LATEST NEWS